Home
Tutorials
Tutorials show you how to use Simcenter STAR-CCM+ for various applications in a step-by-step format with recommendations for setup, initialization and steps of the solution process specific to the application. Macro and simulation files are available for download for a large proportion of cases.
Incompressible Flow
The tutorials in this set illustrate various Simcenter STAR-CCM+ features for incompressible fluid flows as well as porosity and solution recording
Material Calibration: Curve Fitting Non-Newtonian Model Parameters
This tutorial illustrates the workflow for calibrating rheological model parameters from experimental rheological data through curve-fitting.
Viscoelastic Fluid: Extended Pom-Pom Model
In this section of the tutorial, modify the set of models and select the input data for the simulation of a viscoelastic fluid with the eXtended Pom-Pom (XPP) model, then use the Fitting Tool from the Material Calibration model to obtain a fitted curve.
Defining the Rheological Data Types for Non-Linear Viscoelastic Parameter Fitting
The following section calibrates the non-linear parameters using time-uniaxial elongational viscosity data. For this purpose, change the data type to elongational viscosity as a function of time, measured at a constant elongation rate of $\dot{ϵ}$ = 1000 /s. (For transient data, a non-zero rate must be entered, whereas the default is 0.) Only this curve is used to fit the non-linear model parameters.

Share

Link: copied

Breadcrumb: copied

Tutorials
Tutorials show you how to use Simcenter STAR-CCM+ for various applications in a step-by-step format with recommendations for setup, initialization and steps of the solution process specific to the application. Macro and simulation files are available for download for a large proportion of cases.
- Using Tutorial Macros and Files
  Macros, input files, and final simulation files for a range of tutorials are provided as an optional download package on the Support Center website. These macros and final simulation files are provided as an aid to the written tutorials, so that you can check your final results against the downloaded files, or against a simulation that is built and run using the macros.
- Introduction
  Welcome to the Simcenter STAR-CCM+ introductory tutorial. In this tutorial, you explore the important concepts and workflow. Complete this tutorial before attempting any others.
- Foundation Tutorials
  The foundation tutorials showcase the major features of Simcenter STAR-CCM+ in a series of short tutorials.
- Geometry
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for creating and working with parts and 3D-CAD.
- Mesh
  The tutorials in this set illustrate various STAR-CCM+ features for building CFD meshes.
- Incompressible Flow
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for incompressible fluid flows as well as porosity and solution recording
  - Steady Flow: Lid-Driven Cavity Flow
    This tutorial demonstrates the performance of Simcenter STAR-CCM+ in solving a traditional square lid-driven cavity flow. The problem geometry consists of a two-dimensional 1 m² cavity. The cavity is covered by an impermeable wall that moves in the x-direction with constant velocity of 1 m/s. A stretched quadrilateral mesh with 6400 cells is used.
  - Steady Flow: Channel Flow with Multiple Meshes
    This tutorial describes a steady airflow simulation over an obstacle that is mounted at the bottom wall of a three-dimensional channel.
  - Steady Flow: Laminar and Turbulent Flow in an S-Bend
    This tutorial demonstrates the flow of an incompressible gas through an s-bend of constant diameter (2 cm), for both laminar and turbulent flow. The first part of the tutorial covers the laminar flow, with a Reynolds number (Re) of 500, and the second part covers the turbulent flow, Re = 50,000. The same pipe geometry is used in both cases.
  - Steady Flow: Backward Facing Step
    Steady flow over a backward facing step is a typical scenario to investigate the behaviour of reattaching flows. Understanding the behaviour of the flow is crucial for many applications such as designing heat exhangers, evalutating aerodynamic performance and improving flow control strategies.
  - Anisotropic Flow: Cyclone Separator
    The flow inside a cyclone separator is characterised by strong swirling motion and three-dimensional boundary layers. Properly accounting for these effects is a challenging problem for CFD simulations. This tutorial presents the initial step in setting up a coarse mesh cyclone flow simulation.
  - Porous Resistance: Isotropic Media
    This tutorial models flow through a catalyst geometry.
  - Porous Resistance: Orthotropic Media
    This tutorial solves the same problem as the Porous Resistance: Isotropic Media, except that the fluid in the porous region cannot flow in any direction other than the bulk flow (y-) direction.
  - Solution Recording and Playback: Vortex Shedding
    This tutorial demonstrates how to use the solution recording and playback module for capturing the results of transient phenomena.
  - Generalized Newtonian Fluid: Flow in a Static Mixer
    This tutorial demonstrates the process of setting up and analyzing the flow of a viscous fluid through a static mixer.
  - Viscoelastic Flow: Basic Extrusion
    This tutorial illustrates the extrusion of molten rubber through a die.
  - Material Calibration: Curve Fitting Non-Newtonian Model Parameters
    This tutorial illustrates the workflow for calibrating rheological model parameters from experimental rheological data through curve-fitting.
    - Prerequisites
      The Material Calibration: Curve Fitting tutorial assumes that you are already familiar with certain techniques in Simcenter STAR-CCM+.
    - Creating the Simulation and Importing the Experimental Data
      For this tutorial, you start from a new simulation. You import the tables containing the experimental data in .csv format. There is no need to include mesh or geometry.
    - Generalized Newtonian Fluid: Power Law Model
      In this section of the tutorial, set up the models and select the input data for the simulation of a generalized Newtonian fluid, then use the Fitting Tool from the Material Calibration model to obtain a fitted curve for shear rate versus shear viscosity. Use this curve to establish material properties.
    - Viscoelastic Fluid: Extended Pom-Pom Model
      In this section of the tutorial, modify the set of models and select the input data for the simulation of a viscoelastic fluid with the eXtended Pom-Pom (XPP) model, then use the Fitting Tool from the Material Calibration model to obtain a fitted curve.
      - Selecting the Physics Models and Materials
        Select rheology models and input tables to represent a multi-branched polymer described by the eXtended Pom-Pom model.
      - Defining the Rheological Data Type for Linear Viscoelastic Parameter Fitting
        Enter the rheological data for the storage and loss moduli $G'$ and $G "$ as a function of frequency.
      - Curve-Fitting the Linear Model Parameters for One Mode
        To calibrate the model parameters for viscoelastic models, start with the linear parameters polymer relaxation time and polymer viscosity. As before, deactivate all the model parameters, then plot and analyze the general fluid behavior.
      - Curve-Fitting the Linear Viscoelastic Model Parameters for Three Modes
        Add two more viscoelastic modes and enter the parameters for them. This improves the fit with experimental data, at a computational cost for the added modes.
      - Defining the Rheological Data Types for Non-Linear Viscoelastic Parameter Fitting
        The following section calibrates the non-linear parameters using time-uniaxial elongational viscosity data. For this purpose, change the data type to elongational viscosity as a function of time, measured at a constant elongation rate of $\dot{ϵ}$ = 1000 /s. (For transient data, a non-zero rate must be entered, whereas the default is 0.) Only this curve is used to fit the non-linear model parameters.
      - Curve-Fitting the Non-Linear Model Parameters
        Now you fit the non-linear model parameters $Q$ , $1 / ϵ$ , and $α$ using the experimental uniaxial elongational viscosity versus time curve. To obtain an initial value for the relaxation time, you invert the extension rate at which the uniaxial elongational viscosity versus time curve is measured.
    - Curing: Chemorheology Model
      In this section of the tutorial, you set up the models and select the input data for the simulation of a generalized Newtonian fluid that undergoes a curing process. You use the Chemorheology model to account for the changes in rheological properties due to that curing process.
  - Polymer Melt Extrusion: Film Casting
    In industry, film casting is a common process for producing thin polymeric films. Cast films are used for applications such as food and textile packaging, stretch wraps, or plastic bags. Simcenter STAR-CCM+ provides a combination of the Film Casting model and the Free Surface model that allows you to simulate that process and to investigate the impact of various parameters on the resulting film.
- Compressible Flow
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for compressible fluid flows as well as harmonic balance.
- Heat Transfer and Radiation
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for heat transfer, radiation, and thermal comfort.
- Multiphase Flow
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for simulating multiphase fluid flow problems
- Discrete Element Method
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for simulating Discrete Element Method problems
- Motion
  The tutorials in this set illustrate various STAR-CCM+ features for simulating problems with moving geometries and meshes, dynamic fluid body interaction, and rigid body motion:
- Reacting Flow
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for simulating reacting flows such as combustion.
- Solid Stress
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for computing deformation, strain, and stresses in solid regions. They also show how such computations can be coupled to the fluid behavior in an analysis of fluid-structure interaction.
- Aeroacoustics
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for solving aeroacoustic simulations.
- Electromagnetism
  The following tutorials illustrate features for solving problems that involve electromagnetic fields.
- Electrochemistry
  The following tutorial demonstrates chemical reactions induced by an electrical current.
- Battery
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for setting up a battery model:
- Automation
  The tutorials in this set illustrate various Simcenter STAR-CCM+ automation and macro features.
- Design Exploration
  The tutorials in this set illustrate various features for running design exploration studies in Design Manager.
- Coupling with CAE Codes
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for coupling with CAE codes:
- Analysis Methods
  The tutorials in this set illustrate various Simcenter STAR-CCM+ features for analysing and visualizing simulation data.
- Simcenter STAR-CCM+ In-cylinder
  The tutorials in this set illustrate features for simulating internal combustion engines in Simcenter STAR-CCM+ using the dedicated add-on Simcenter STAR-CCM+ In-cylinder.

Defining the Rheological Data Types for Non-Linear Viscoelastic Parameter Fitting

The following section calibrates the non-linear parameters using time-uniaxial elongational viscosity data. For this purpose, change the data type to elongational viscosity as a function of time, measured at a constant elongation rate of $\dot{ϵ}$ = 1000 /s. (For transient data, a non-zero rate must be entered, whereas the default is 0.) Only this curve is used to fit the non-linear model parameters.

To define the rheological data type:

Right-click the Material Calibration > Inputs node and select Add Input Table.
Rename the new input table as ElongationalViscosity Table.

Select the Inputs > ElongationalViscosity Table node and set the following properties:


Property	Value
Data Table	elongationalViscosity_time
Input Type	Time - UniAxial Elongational Viscosity

Select the ElongationalViscosity Table > Rate Specification node and set Rate to 1000 /s.
Select the Inputs > GpGpp Table node and deactivate Active.